View 33-01-G4C-ARTB08_701338.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Technical Data Sheet 3mm POWER LED
33-01/G4C-ARTB
Benefits
. High Flux Output. . Low Profile. . Low Thermal Resistance. . Low Power Consumption. .The product itself will remain within RoHS compliant version. . ESD-withstand voltage: up to 4KV.
Descriptions
This revolutionary package design allows the light designer to reduce the number of LEDs required and provide a more uniform and unique illuminated appearance than with other LED solutions. This is possible through the efficient optical package design and high-current capabilities. The low profile package can be easily coupled with reflectors or lenses to efficiently distribute light and provide the desired light appearance.
Applications
. Automotive Exterior Lighting . Electronic Signs and Signals . Channel Letter . Special Lighting application
Device Selection Guide
PART NO. 33-01/G4C-ARTB Chip Material InGaN Emitted Color Brilliant Green Lens Color Water Clear
Everlight Electronics Co., Ltd. Device number: DPE-0000057
http:\\www.everlight.com Established date: 05-30-2008
Rev.1
Page: 1 of 10
Established by: Jim Lin
Technical Data Sheet 3mm POWER LED
33-01/G4C-ARTB
Package Dimensions
Notes: 1.All dimensions are in millimeters 2.An epoxy meniscus may extend about 1.5mm(0.059") down the leads 3.Tolerances unless dimensions 0.25mm
Absolute Maximum Ratings (Ta=25)
Parameter Continuous Forward Current Peak Forward Current(Duty 1/10 @ 1KHZ) Operating Temperature Storage Temperature Soldering Temperature(T=5 sec) Power Dissipation Zener Reverse Current Electrostatic Discharge LED Junction Temperature
Everlight Electronics Co., Ltd. Device number: DPE-0000057
Symbol IF IFP Topr Tstg Tsol Pd Iz ESD Tj
http:\\www.everlight.com Established date: 05-30-2008
Rating 30 100 -40 ~ +85 -40 ~ +100 260 5 120 100 4K 110
Rev.1
Units mA mA mW mA V
Page: 2 of 10
Established by: Jim Lin
Technical Data Sheet 3mm POWER LED
33-01/G4C-ARTB
Electro-Optical Characteristics (Ta=25)
Parameter Total Flux Viewing Angle Peak Wavelength Dominant Wavelength Forward Voltage Reverse Current Zener Reverse Voltage Symbol v 21/2 p d VF IR Vz Min. 4500 ------520 3.0 ---5.2 Typ. 5650 90 518 525 ---------Max. 9000 ------532 4.0 10 ---Condition IF=30mA IF=30mA IF=30mA IF=30mA IF=30mA VR=5V Iz=5mA Unit mlm deg Nm Nm V uA V
Rank 33-01/G4C-ARTB (1) VF(V)
Bin. 1 2 3 4 5 Min. 3.00 3.20 3.40 3.60 3.80 Max. 3.20 3.40 3.60 3.80 4.00
(1)
(2) (2) d
(3) (3)v(mlm)
Max. 524 528 532 Bin. R S T Min. 4500 5650 7150 Max. 5650 7150 9000
Bin. 3 4 5
Min. 520 524 528
*Measurement Uncertainty of Forward Voltage0.1V *Measurement Uncertainty of Total Flux: 15% *Measurement Uncertainty of Dominant Wavelength 1.0nm
Everlight Electronics Co., Ltd. Device number: DPE-0000057
http:\\www.everlight.com Established date: 05-30-2008
Rev.1
Page: 3 of 10
Established by: Jim Lin
Technical Data Sheet 3mm POWER LED
33-01/G4C-ARTB
Typical Electro-Optical Characteristics Curves
Relative Intensity vs. Wavelength
1.00
Forward Current vs. Forward Voltage
30
FORWARD CURRENT (mA)
RELATIVE INTENSITY
20
0.50
10
0.00 450 475 500 525 550 575 600 625 650 WAVELENGTH (nm)
0 2.80
3.00 3.20 3.40 3.60 3.80 FORWARD VOLTAGE (V)
4.00
Relative Intensity vs. Forward Current
1.00
Forward Current vs. Ambient Temp.
40 35
RELATIVE INTENSITY
0.80
FORWARD CURRENT (mA)
0 5 10 15 20 25 30
30 25 20 15 10 5
0.60
0.40
0.20
0.00
0
FORWARD CURRENT (mA)
0
20 40 60 80 AMBIENT TEMPERATURE (C)
100
Relative Intensity vs. Displacement Angle
0
1.00
Relative Intensity (a.u.)
15 30 45 60 75
0.75 0.50 0.25 0.00 -90 -75 -60 -45 -30 -15 0 Viewing angle (degree)
90
Everlight Electronics Co., Ltd. Device number: DPE-0000057
http:\\www.everlight.com Established date: 05-30-2008
Rev.1
Page: 4 of 10
Established by: Jim Lin
Technical Data Sheet 3mm POWER LED
33-01/G4C-ARTB
Packing Specification 1. Tube
Cross section image of tube
Unit: mm
Whole image of tube
Tube Label ANTISTATIC
4852mm
2. Inner Box
Box Label
Everlight Electronics Co., Ltd. Device number: DPE-0000057
http:\\www.everlight.com Established date: 05-30-2008
Rev.1
Page: 5 of 10
Established by: Jim Lin
Technical Data Sheet 3mm POWER LED
33-01/G4C-ARTB
3. Outside Box
Box Label
4. Packing Quantity
(1) 60 pcs/1 tube, 30 tubes/1 small inside box, 12 small inside boxes/1 outside box. (2) 60 pcs/1 tube, 105 tubes/1 big inside box, 4 big inside boxes/1 outside box.
Label Form Specification
(1)Tube Label Form
PART NO: 33-01/G4C-ARTB LOT NO: QTY: 60 CAT:
(2)Box Label Form EVERLIGHT CPN: P/N:
RoHS PART NO: Everlgiht's Production Number QTY: Packing Quantity LOT NO: Lot Number CAT: Ranks of Forward Voltage, Color Bin Grade and Total Flux
33-01/G4C-ARTB QTY LOT NO MADE IN TAIWAN
CAT: HUE: REF:
CPN: Customer's Production Number P/N : Production Number HUE: Reference REF: Reference MADE IN TAIWAN: Production Place
Everlight Electronics Co., Ltd. Device number: DPE-0000057
http:\\www.everlight.com Established date: 05-30-2008
Rev.1
Page: 6 of 10
Established by: Jim Lin
Technical Data Sheet 3mm POWER LED
33-01/G4C-ARTB
Notes
1. Lead Forming During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb. Lead forming should be done before soldering. Avoid stressing the LED package during leads forming. The stress to the base may damage the LED's characteristics or it may break the LEDs. Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures may cause failure of the LEDs. When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead position of the LED. If the LEDs are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs. 2. Storage The LEDs should be stored at 30C or less and 70%RH or less after being shipped from Everlight and the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material. Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can occur. 3. Soldering Careful attention should be paid during soldering. Solder the LED no lower than 1.6mm from the base of stopper is recommended. Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering. Recommended soldering conditions: Hand Soldering
Temp. at tip of iron Soldering time Distance 300 Max. (30W Max.) 3 sec Max. No lower than 1.6mm from the base of stopper Distance No lower than 1.6mm from the base of stopper Preheat temp. Bath temp. Bath time.
DIP Soldering
100 Max. (60 sec Max.) 260 Max. 5 sec Max.
Avoiding applying any stress to the lead frame while the LEDs are at high temperature
Everlight Electronics Co., Ltd. Device number: DPE-0000057 http:\\www.everlight.com Established date: 05-30-2008 Rev.1 Page: 7 of 10
Established by: Jim Lin
Technical Data Sheet 3mm POWER LED
33-01/G4C-ARTB
particularly when soldering. Dip and hand soldering should not be done more than one time After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return to room temperature. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. Although the recommended soldering conditions are specified in the above table, dip or handsoldering at the lowest possible temperature is desirable for the LEDs. Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder wave. 4. Cleaning When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a duration of no more than one minute. Dry at room temperature before use. Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Ultrasonic cleaning shall be pre-qualified to ensure this will not cause damage to the LED 5. Circuit Protection Below the zener reference voltage Vz, all the current flows through LED and as the voltage rises to Vz, the zener diode "breakdown." If the voltage tries to rise above Vz current flows through the zener branch to keep the voltage at exactly Vz. When the LED is connected using serial circuit, if either piece of LED is no light up but current can't flow through causing others to light down. In new design, the LED is parallel with zener diode. if either piece of LED is no light up but current can flow through causing others to light up.
Everlight Electronics Co., Ltd. Device number: DPE-0000057
http:\\www.everlight.com Established date: 05-30-2008
Rev.1
Page: 8 of 10
Established by: Jim Lin
Technical Data Sheet 3mm POWER LED
33-01/G4C-ARTB
6. Heat Management Heat management of LEDs must be taken into consideration during the design stage of LED application. The current should be de-rated appropriately by referring to the de-rating curve found in each product specification. The temperature surrounding the LED in the application should be controlled. Please refer to the data sheet de-rating curve. 7. ESD (Electrostatic Discharge) Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs. An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling LEDs. All devices, equipment and machinery must be properly grounded. Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing. 8. Other Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets.
Everlight Electronics Co., Ltd. Device number: DPE-0000057 http:\\www.everlight.com Established date: 05-30-2008 Rev.1 Page: 9 of 10
Established by: Jim Lin
Technical Data Sheet 3mm POWER LED
33-01/G4C-ARTB
These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don't reproduce or cause anyone to reproduce them without EVERLIGHT's consent.
EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http:\\www.everlight.com
Everlight Electronics Co., Ltd. Device number: DPE-0000057
http:\\www.everlight.com Established date: 05-30-2008
Rev.1
Page: 10 of 10
Established by: Jim Lin

▲Up To Search▲

Price & Availability of 33-01-G4C-ARTB08

	To Download 33-01-G4C-ARTB08 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .